Setting up A Bathtub
Setting up A Bathtub
Blog Article
Here down the page you can locate some sensible data in regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a bathtub isn't precisely rocket science, however it does require strong plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably tough task. If the old bathtub is readily available, the task can move quickly; if you need to open up a wall surface to eliminate the old bathtub and position the brand-new bath tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly need an assistant to move out the old tub and set in the new one. Ensure you have actually certified yourself for the task and also are comfortable trying it. Rather than employing a contractor to take over a halfway-completed job, it is far better to consider utilizing one prior to you start. Chances are you may require a specialist plumber to make tube connections.
This short article will certainly aid you mount a new tub in your shower room if you have actually already purchased a new tub as well as do not require to change the arrangement of your previous water system pipes.
Your devices and also product list must consist of the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is detach the water. After doing so, turn on the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be rather bothersome because of the limited access that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will originate from the pipes. When the supply pipelines have actually been removed, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming during this process. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to moving on to fit the new faucets, contrast the pipe links on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin making certain that the washers remain in place between the faucet and the sink. Protect the tap in place with the maker provided backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The former kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Bathtub
Utilizing both wooden boards under its feet, position the bathtub in the needed position. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
The next objective is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bathtub up until the level reads level.
To mount taps, fit the bottom of the outermost flexible tap port to the ideal supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water and check all joints as well as brand-new pipework for leaks and tighten them if needed. Fill up the bath tub as well as also check the overflow electrical outlet as well as the regular electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the maker's user's manual. Tiling and sealing around the tub must wait till the bathtub has been utilized at the very least when as this will settle it right into its last position.
Preparing for the Installation
First of all, the sustaining structure provided with the bathroom should be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the adaptable faucet adapters to the bottom of the two taps using 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, resulting in complications with wetness and also feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, and are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of soaked paper or soft rope. Keep in mind to always load the bath tub with water before sealing, to permit the movement experienced when the bathtub remains in use. The sealant can fracture relatively early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
I was introduced to that write-up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through someone on our other web address. If you liked our article please don't forget to share it. I thank you for reading our article about Tools You Need to Install a New Bathtub .
Get Quote
Report this page